VNC not running on the specified port range.Also make sure the server is started by using service vncserver start. When running the vncserver command, set the password as the correct user. Make sure you log in with the correct user/password combination. Reasons why you may get a “connection was refused” error: VNC Viewer the Connection was Refused by the Computer If you have gone through all the above steps but you are still experiencing a problem, then log a support ticket with RealVNC here. If none of the previous steps helped, restart the VNC Server itself and the computer, which is running it.Сheck the RealVNC status page for service issues.If you’re using Linux, establish that the Linux display server protocol Wayland is disabled.For subscription users, verify that you are attempting to join your computer with the correct paid-for team.Have you selected the correct team for the remote computer?.Is “Allow cloud connections” checked in your VNC Server settings?.It is recommended that you configure the power options to ensure it never goes to sleep. Make sure that the server is not in sleep mode.The remote computer or server must be connected to the Internet in order for you to connect to it.# I'm running GNOME (installed using sudo yum install gnome-*)Ĭonnect using Tiger 32-bit VNC Client v1.3.1 on Windows 7.Step through the following checklist to resolve the problem: # Xvnc is started by vncserver with following args: # I start the server using vncserver -geometry 800圆00 Versions with which it works for me right now (although I've not had issues with ANY versions in the past, I just install the latest using yum install gnome-* tigervnc-server and works fine): OS: RHEL 6.6 (Santiago) I tried all I could to add a new resolution to the xrandr, but to no avail, always end up with 'xrandr: Failed to get size of gamma for output default' error. With this the resolution changes to fit the size of the client window no matter what it is, and it's not zooming, it's actual resolution change (I can see the new resolution in xrandr output). Windows some version with Tiger VNC Client.but it resizes when I change the TigerVNC Client window. I don't know what the TigerVNC client tells remote vncserver or xrandr or Xvnc or gnome or. Perhaps the most ignorant answer I've posted but here goes: Use TigerVNC client/viewer and check 'Resize remote session to local window' under Screen tab of options. Line: VNC-0 connected 1600x900+0+0 0mm x 0mmīind the new modeline to the current VNC virtual monitor: $ xrandr -addmode VNC-0 "2560x1600_60.00" In the above xrandr output look for the display name on the second Or if the monitor is old get the GTF timings: $ gtf 2560 1600 60 List the modeline (see xrandr article in ArchLinux wiki) for Screen 0: minimum 32 x 32, current 1600 x 900, maximum 32768 x 32768Īnd you'll notice the screen being quite small. Once inside the VNC session start up a terminal window.Ĭonfirm that the new geometry is available in the VNC session: $ xrandr On the "2560x1600" computer start the VNC viewer (I prefer Start a VNC session with a geometry matching the physical display: $ vncserver -geometry 1600x900 :1 The computer with the resolution of "1600x900": With that background if the goal is to share a VNC session between twoĬomputers with the above resolutions and assuming that the VNC server is There must be a way to add custom modelines and man xrandr confirms Think the developers who wrote the code are much smarter and the hardĬoded list is just a sample of values. Xrandr allows selecting the display modes (a.k.a resolutions) howeverĪny additional modeline such as "2560x1600" or "1600x900" would need to I'm using TightVnc viewer as the client and it automatically adapts to the new resolution.Īs this question comes up first on Google I thought I'd share a solution using TigerVNC which is the default these days. I can then easily switch to another resolution (f.e. When I run xrandr in a terminal, it displays all the available screen resolutions: bash> xrandr I just start vncserver without any -randr or multiple -geometry options. I'm running TigerVNC on my Linux server, which has basic randr support.
0 Comments
Leave a Reply. |